ford sync not working after battery change

You have to give the reset system a time and do not disturb this process. Press and hold both the Volume Down and Seek Right buttons on the steering wheel controls for 10 seconds.

Sync 3 How To Perform A Master Reset Ford How To Ford Youtube

I tried factory reset and master reset already.

. Now that same button just lowers the volume. Pull fuse 32 or 33 its one of these two I just cant remember on the cabin fuse panel or disconnect the negative terminal on the battery. The first thing to do if you run into Ford Sync Bluetooth audio not working is to completely restart the vehicles system.

Disconnect your phone or device from the USB port. 2016 Ford Flex SE. Locate the PHONE button in your center stack location will vary by model.

From here select Advanced System Settings and then select Master Reset. Download this package ZIP 44KB and extract it on a USB stick the USB stick needs to in ex-fat format Enter your vehicle and switch on the engine. Here is the procedure 1- Pressed the mode switch several times to make sure I did not put the.

If you have Navi you go to the screen to download or install. I have a 62 reg Ford Fiesta with Sync. The first thing to do if you run into Ford Sync Bluetooth audio not working is to completely restart the vehicles system.

By zighawk Thu Dec 12 2019 821 pm. When you press the lock button the ECU will save the settings and reset the key fob. Weird Problem After Battery Change.

You will hear the lock sound caused by the above process. Dealer fitted accessories are fitted after registration and could have an impact on your vehicles fuel. To do a master reset go into the Settings menu and select General.

This should now have produced a new log file. Tap SYNC to connect. Locate the DIRECTIONAL and OK BUTTONS in the center stack location will vary.

Find the Bluetooth menu on your phone. You can also check your owners manual for any. This means turning the ignition off and opening and closing the door to reset the computer.

3- Removed the two screws holding the unit to the ceiling and pulled the unit. Find your phones Bluetooth menu. I did it just by removing the ground.

When Sync 3 is fully loaded insert the USB stick. Normally I press a button on my steering wheel and it says Sync - please say a command. The system reset is designed to restore functionality that has stopped working and does not delete any data that you have stored.

To question my ability to. You will have to delete your phone from the system of the car. To do this first go to your phones settings and turn Bluetooth off and then back on.

Herculean strength isnt necessary but the cables should be snug and not move around or come off of the battery posts. After a time of around 3-5 minutes the screen turns to blank. Your Ford key fob not working after a battery change is probably caused by the battery change itself.

My battery was flat this morning the garage replaced it but now Sync is being weird. Phone feature stopped working after battery died. The sync line in doesnt work either.

Listen to the Lock Sound. That will power off the sync module and allow it to reboot should work fine after rebooting. Doing a Ford Sync Master Reset.

First and foremost disconnect your phone and un-pair it from the SYNC device. This is why nothing is operating with your key fob remote. There are a few different reasons for a car radio to stop working after the battery has gone completely dead.

Looking back on the 2013-16 pages Sync seems to have a history of funky behavior including apparent death followed by. Thanks for your advise. After I did the reset the phone button on the radio doesnt work and I cant access the sync-phone source at all or even get into the options.

Following this go to your Syncs settings and do the exact same thing. Also disable the Bluetooth on your phone. Fiesta with Sync.

You have to press the seek-up and radio power button for a while. Through MyFord Touch you will press phone then Bluetooth devices in settings select your phone and finally delete it. Therefore you have to press the lock button within five seconds after the lock sound.

The first and easiest thing you should try to do to stop Ford Sync not working at all is simply resetting the connection. Wait until an installation complete message appears it may take approximately 1 minute. My girlfriend and I didnt a lot of research and found something about removing the fuse for SYNC in the passenger fuse box behind the.

None of the mechanical button inputs worked -- radio power DISP steering wheel controls etc. In the end resume the sync system. If youre experiencing electrical issues immediately after a battery replacement or disconnect make sure the battery cables were re-attached and tightened down properly.

If the connection times out or attempts to take longer than a minute cancel the connection on your phone and go to Tip 4. Once its finished try setting up your Ford Sync system again from scratch and see if that fixes the issue. Wait for the system to fully shut down and then wait an additional 30 seconds.

No change still had all the errors wouldnt start. Before and after renting a vehicle. The key fob must be reset to the car after replacing the battery in the key fob remote as the key was erased when the battery was changed.

Enter your four-digit PIN code and then select Erase Everything. From the front to release the two clips. Press Menu Sync Settings press OK Install on Sync press OK Select Yes.

Press and hold both the Power button center of the volume knob and the Seek Right button for 10 seconds. I just bought a used 2019 Ford Fusion and Ive deleted all devices off sync manually as well as a master reset. By Gumby Tue Jul 12 2011 1037 pm.

Manually connect the phone with SYNC. Next SYNC will notify that all. Failure to do this will delete data from your device.

This will last from 10 to 20 minutes depending on the size of the installed file. So my Sync 3 worked fine on the way to Walmart -- but when I started it up to come home the Sync 3 screen was completely black. The sound indicates that you are in programming mode.

So I downloaded the status checker tool put it on a thumb drive and stuck it in the USB port - and absolutely nothing happened. An audio message will play SYNC will start rebooting to update. All the activity recovers in few minutes approximately 5 minutes.

So as an update I followed the advice above and disconnected the battery and left it for ten minutes yesterday morning. Phone feature stopped working after battery died. Unit in the blank mode accidently did not work 2- Checked the 75 A fuse number 10 and it was Ok.

Ford Sync Bluetooth Fix Youtube